Персона: Гурова, Юлия Александровна
Загружается...
Email Address
Birth Date
Научные группы
Организационные подразделения
Организационная единица
Институт ядерной физики и технологий
Цель ИЯФиТ и стратегия развития - создание и развитие научно-образовательного центра мирового уровня в области ядерной физики и технологий, радиационного материаловедения, физики элементарных частиц, астрофизики и космофизики.
Статус
Фамилия
Гурова
Имя
Юлия Александровна
Имя
10 results
Результаты поиска
Теперь показываю 1 - 10 из 10
- ПубликацияТолько метаданныеBrazing tungsten/tantalum/RAFM steel joint for DEMO by fully reduced activation brazing alloy 48Ti-48Zr-4Be(2021) Somov, P.; Bachurina, D.; Suchkov, A.; Gurova, J.; Kliucharev, V.; Vorkel, V.; Savelyev, M.; Sevryukov, O.; Сучков, Алексей Николаевич; Гурова, Юлия Александровна; Савельев, Максим Дмитриевич; Севрюков, Олег Николаевич© 2021 by the authors. Licensee MDPI, Basel, Switzerland.To create a DEMO reactor, it is necessary to develop high-quality technology to join tungsten with reduced-activation ferritic-martensitic (RAFM) steel (Rusfer, Eurofer, CLF-1, etc.). Diffi-culties arise in their direct connection due to the large difference in the coefficient of thermal expan-sion (CTE). To suppress the difference of CTE, intermediate interlayers are usually used, such as vanadium or tantalum, and brazing is a prospective technology to conduct the joining. The vast majority of works represent copper-or nickel-based brazing alloys, but their applicability is under significant discussion due to their activation properties. That is why, in this work, fully reduced activation 48Ti-48Zr-4Be wt.% brazing alloy was used. The following joint was made: Rusfer steel/48Ti-48Zr-4Be/Ta/48Ti-48Zr-4Be/W. The brazing was successfully carried out under a mode providing thermal heat treatment of Rusfer. Through EDS and EBSD analysis, the microstructure of the joint was determined. Shear strength of the as-joined composition was measured as 127 ± 20 MPa. The joint endured 200 thermocycles in the temperature range between 300-600 °C, but the fillet regions degraded.
- ПубликацияТолько метаданныеHigh-temperature brazing of structural elements for the first wall of the DEMO reactor with rapidly hardened tungsten and steel alloys-solders(2019) Bachurina, D. М.; Suchkov, A. N.; Gurova, Y.; Sevryukov, O. N.; Сучков, Алексей Николаевич; Гурова, Юлия Александровна; Севрюков, Олег Николаевич© 2021 Informa UK Limited, trading as Taylor & Francis Group.The work presents the results of high-temperature brazing of reduced activated ferritic martensitic steel EK-181 with pure tungsten, which is essential for DEMO fusion reactor. To reduce thermal stresses, vanadium interlayer was used. Brazing alloys to be used were rapidly quenched into ribbons Cu-28Ti and Cu-28Sn for EK-181/V, Cu-50Ti for V/W. Microstructure investigations, mechanical and thermocycling test were carried out. It is shown that Cu-28Ti is better to use; however, it is necessary to improve the reliability of V/W seam.
- ПубликацияТолько метаданныеInvestigation of a brazed joint EK-181/V/W obtained by Cu-Sn and Cu-Ti amorphous foils(2020) Bachurina, D.; Suchkov, A.; Gurova, Y.; Sevryukov, O.; Сучков, Алексей Николаевич; Гурова, Юлия Александровна; Севрюков, Олег Николаевич© Published under licence by IOP Publishing Ltd.The work presents the results of high temperature brazing of reduced activated ferritic martensitic steel EK-181 with pure tungsten, which is essential for DEMO fusion reactor. Vanadium interlayer was used to reduce thermal stresses. Brazing alloys to be used were rapidly quenched into ribbons Cu-12Sn, Cu-20Sn, Cu-12Sn-0,4P for EK-181/V, Cu-50Ti for V/W. Microstructure investigations, mechanical and thermocycling test were carried out.
- ПубликацияТолько метаданныеBrazing SMART tungsten alloys to RAFM steels by Titanium-Zirconium-Beryllium brazing alloy(2024) Kirillova, V. O.; Popov, N. S.; Gurova, J. A.; Fedotov, I. V.; Suchkov, A. N.; Кириллова, Вероника Олеговна; Попов, Никита Сергеевич; Гурова, Юлия Александровна; Федотов, Иван Владимирович; Сучков, Алексей Николаевич
- ПубликацияОткрытый доступМИКРОСТРУКТУРА И МЕХАНИЧЕСКИЕ СВОЙСТВА ПАЯНЫХ СОЕДИНЕНИЙ SMART СПЛАВОВ ВОЛЬФРАМА И МАЛОАКТИВИРУЕМЫХ ФЕРРИТНО-МАРТЕНСИТНЫХ СТАЛЕЙ(НИЯУ МИФИ, 2023) КИРИЛЛОВА, О. В.; БАЧУРИНА, Д. М.; ГУРОВА, Ю. А.; ПОПОВ, Н. С.; ТАН, Ш.; СУЧКОВ, А. Н.; Попов, Никита Сергеевич; Кириллова, Вероника Олеговна; Гурова, Юлия АлександровнаРазработка демонстрационного термоядерного реактора ДЕМО является необходимым шагом для освоения термоядерной энергетики. В качестве материалов, обращенных к плазме, предполагается использование вольфрама или его сплавов, а в качестве конструкционного материала — малоактивируемых ферритно-мартенситных сталей. Особый интерес представляют так называемые SMART сплавы вольфрама [1-2], которые разработаны для того, чтобы предотвратить окисление вольфрама в случае возникновения аварии. В то же время, существует целый ряд различных марок малоактивируемых ферритно-мартенситных сталей, каждая из которых требует своего режима термообработки. Целью данной работы являлось изучить микроструктуру и свойства паяных соединений оценить SMARTсплавов WCrY и WCrZr с ферритно-мартенситными сталями Eurofer и CLAM.
- ПубликацияОткрытый доступDeuterium retention in the elements of plasma facing components for the DEMO first wall(2022) Bobyr, N.; Kulikova, E.; Gasparyan, Y.; Bachurina, D.; Efimov, V.; Gurova, J.; Podolyako, F.; Sergeev, N. S.; Sorokin, I. A.; Suchkov, A.; Kozlov, I.; Spitsyn, A. V.; Гаспарян, Юрий Микаэлович; Ефимов, Виталий Сергеевич; Гурова, Юлия Александровна; Подоляко, Федор Сергеевич; Сергеев, Никита Сергеевич; Сорокин, Иван Александрович; Сучков, Алексей Николаевич; Козлов, Илья Владимирович© 2022 Elsevier B.V.The fully reduced activation brazing alloy TiZr4Be and a tantalum intermediate layer are considered to be used for joining tungsten (W) to reduced-activation ferritic-martensitic steel (RAFM) for future DEMO reactor application. Deuterium retention in the W-Rusfer joints and separate elements was investigated with the focus on the intermediate brazing layer. The samples were exposed in deuterium gas (p = 1–104 Pa, T = 300–600°C) and plasma discharge (T = 600°C). An acceptable deuterium concentration was observed after gas exposure at the pressure of 1 Pa, that is relevant to operating conditions of future fusion devices, however the brazing alloy and tantalum accumulate a large amount of deuterium in the case of the pressure above 100 Pa that leads to failure of the joint. The D retention after D plasma irradiation was substantial, but nearly independent on the fluence and the thickness of the W layer due to absorption from surrounding D2 gas.
- ПубликацияОткрытый доступOverview of the mechanical properties of tungsten/steel brazed joints for the demo fusion reactor(2021) Bachurina, D.; Vorkel, V.; Suchkov, A.; Gurova, J.; Ivannikov, А.; Penyaz, M.; Fedotov, I.; Sevryukov, O.; Kalin, B.; Сучков, Алексей Николаевич; Гурова, Юлия Александровна; Иванников, Александр Александрович; Федотов, Иван Владимирович; Севрюков, Олег Николаевич© 2021 by the authors. Licensee MDPI, Basel, Switzerland.A Demonstration (DEMO) thermonuclear reactor is the next step after the International Thermonuclear Experimental Reactor (ITER). Designs for a DEMO divertor and the First Wall require the joining of tungsten to steel; this is a difficult task, however, because of the metals’ physical properties and necessary operating conditions. Brazing is a prospective technology that could be used to solve this problem. This work examines a state-of-the-art solution to the problem of joining tungsten to steel by brazing, in order to summarize best practices, identify shortcomings, and clarify mechanical property requirements. Here, we outline the ways in which brazing technology can be developed to join tungsten to steel for use in a DEMO application.
- ПубликацияОткрытый доступInvestigation of microstructure and deuterium retention in the reduced activation tungsten-steel brazed joint(2023) Gurova, J.; Bachurina, D.; Kozlov, I.; Efimov, V.; Krutikova, O.; Suchkov, A.; Spitsyn, A.; Gasparyan, Y.; Гурова, Юлия Александровна; Козлов, Илья Владимирович; Ефимов, Виталий Сергеевич; Крутикова, Ольга Михайловна; Сучков, Алексей Николаевич; Гаспарян, Юрий Микаэлович
- ПубликацияОткрытый доступИССЛЕДОВАНИЕ ПРИМЕНИМОСТИ СПЛАВА-ПРИПОЯ TiZr4Be ДЛЯ ПАЙКИ САМОПАССИВИРУЮЩИХСЯ ВОЛЬФРАМОВЫХ СПЛАВОВ СО СТАЛЬЮ ДЛЯ ТЕРМОЯДЕРНОГО РЕАКТОРА DEMO(НИЯУ МИФИ, 2022) ГУРОВА, Ю. А.; СУЧКОВ, А. Н.; БАЧУРИНА, Д. М.; ПОПОВ, Н. С.; СЕВРЮКОВ, О. Н.; ЛИТНОВСКИЙ, А. М.; ТАН, Ш.; Попов, Никита Сергеевич; Сучков, Алексей Николаевич; Гурова, Юлия АлександровнаТермоядерный реактор DEMO (DEMOnstration Power Plant) — это следующий шаг на пути к созданию промышленной термоядерной электростанции. Проекты DEMO разрабатываются во всем мире.
- ПубликацияОткрытый доступJoining tungsten with steel for DEMO: Simultaneous brazing by Cu-Ti amorphous foils and heat treatment(2021) Svetogorov, R.; Bachurina, D.; Suchkov, A.; Gurova, J.; Savelyev, M.; Dzhumaev, P.; Kozlov, I.; Leont'eva-Smirnova, M.; Sevryukov, O.; Сучков, Алексей Николаевич; Гурова, Юлия Александровна; Савельев, Максим Дмитриевич; Джумаев, Павел Сергеевич; Козлов, Илья Владимирович; Леонтьева-Смирнова, Мария Владимировна; Севрюков, Олег Николаевич© 2020Development of a reliable technology to join tungsten with steel is essential for DEMO application; however, it is difficult due to large differences in their physical properties. To solve this problem, high-temperature brazing was carried out. Cu-Ti brazing alloys, which were rapidly solidified into foil, were used together with a compensating vanadium interlayer, so the EK-181 steel/Cu-28Ti/V/Cu-50Ti/W and EK-181/Cu-50Ti/V/Cu-50Ti/W brazed joints were obtained. The microstructures of the seams were investigated by optical microscopy, SEM (EDX, EBSD) and synchrotron XRD. Thermocycling and shear strength tests showed that Cu-28Ti wt. % brazing alloy ensures a firmer joint compared to Cu-50Ti wt. %. The Cu-28Ti wt. % brazing alloy was used to perform high-temperature brazing in the brazing mode equivalent to traditional EK-181 steel heat treatment. It showed that every step of the heat treatment affected the microstructures and the shear strength.