Персона:
Садовский, Ярослав Алексеевич

Profile Picture
Email Address
Birth Date
Научные группы
Организационные подразделения
OrgUnit Logo
Организационная единица
Институт лазерных и плазменных технологий
Стратегическая цель Института ЛаПлаз – стать ведущей научной школой и ядром развития инноваций по лазерным, плазменным, радиационным и ускорительным технологиям, с уникальными образовательными программами, востребованными на российском и мировом рынке образовательных услуг.
Статус
Фамилия
Садовский
Имя
Ярослав Алексеевич
Имя

Фильтры

2011 - 20203
21
3
Сброс фильтров

Настройки

End date: 2020 × Start date: 2011 ×

Результаты поиска

Теперь показываю 1 - 3 из 3
  • Уменьшенное изображение
    Публикация
    Открытый доступ
    Газообмен между водородной плазмой с примесью кислорода и поверхностью нержавеющей стали
    (НИЯУ МИФИ, 2011) Садовский, Я. А.; Садовский, Ярослав Алексеевич; Беграмбеков, Л. Б.
  • Уменьшенное изображение
    Публикация
    Открытый доступ
    Behavior of B4C coating on tungsten under exposition on T-10 tokamak plasma
    (2019) Begrambekov, L. B.; Grunin, A. V.; Sadovsky, Ya. A.; Беграмбеков, Леон Богданович; Садовский, Ярослав Алексеевич
    © Published under licence by IOP Publishing Ltd.It was shown (Buzhinsky, 2003) that in situ renewable coating of boron carbide can protect the tiles of the divertors of thermonuclear facilities from destruction and also to prevent accumulation of remarkable amounts of tritium in the plasma facing materials. In the paper presented a plasma method for deposition of boron carbide coating with a high adhesion to tungsten was developed. In the laboratory installation boron carbide coating on tungsten was subjected to cycling irradiation by the deuterium ion flux with power density up to 5.0 MW/m2 in the temperature range up to 1500 K. The results of the tests showed that the composition, integrity and adhesion of the coating were not violated in the laboratory tests. In the T-10 tokamak the behavior of the coating was investigated in the temperature range up to 3600 K when irradiated with plasma power in the range of 20-100 MW/m2 during plasma disruption. Being irradiated in T-10 tokamak, the coating retained its continuity, adhesion and protected tungsten from the effect of the even at temperatures of 2500-3600 K, when the coating melted under irradiation and its composition changed to B:C ≈ 1:1.
  • Уменьшенное изображение
    Публикация
    Только метаданные
    Development of Quality Tungsten Coating on Ceramics as a Microwave Shield for ITER High-Frequency Magnetic Sensor
    (2020) Ma, Y.; Vayakis, G.; Shigin, P.; Walsh, M.; Begrambekov, L.; Gordeev, A.; Sadovsky, Y.; Zakharov, A.; Беграмбеков, Леон Богданович; Гордеев, Алексей Алексеевич; Садовский, Ярослав Алексеевич; Захаров, Андрей Михайлович
    © 2019, © 2019 American Nuclear Society. High-quality tungsten coating deposition on sintered aluminum nitride ceramic substrates (both of thin flat chips and structural boxes) was realized using an adapted plasma-aided coating deposition rig. The tungsten coating produced using this technique and the accompanying apparatus setup are of high-purity, strong adhesion, and controlled three-dimensional uniformity (<20% thickness variations). The coating also exhibits well-structured and smooth (Ra < 1.0 µm) microscopic surface landscape with densely clustered tungsten granulations. The coated samples were tested under load conditions expected during ITER operation, including thermal cycling and superheated (up to 500°C) steam. Exposure to thermal cycles and hot steam made no apparent changes to the coating’s microscopic structure with no sign of cracks, blistering, or exfoliation seen under electron microscopy. These successes validated the microwave shield design for the ITER high-frequency magnetic sensor, which is based on this concept, and laid a solid foundation for the production of this component in the forthcoming procurement phase. Besides, a failure test was conducted for the tungsten coating in the temperature range of 500°C to 1500°C. Surface smoothing, pores, delamination, and mass loss in substrate were observed when temperature exceeded 1000°C, possibly due to the evaporation of aluminum atoms. These findings unveiled the changes of tungsten coating properties under extreme conditions that are of both academic and practical values.